High Temperature PVC Push Fit Tubing / Pipe. 50mm diameter, angled boss adaptor, quick fit push tubing. Insert the desired size rubber reducing boss to quickly connect onto 42mm or 50mm soil pipe. One end is enlarged to take the reducing rubber seals, the other end is 50mm to work with the push fit plastic range. Quickly and easily assemble drainage works or use as drainage pipework from combi ovens. Can withstand temperatures of up to 95 degrees C.

• Pipes and fittings manufactured in a single-layer technology, with a thick-walled section, using a perfected raw material formula
• 100% recyclable pipes and fittings
• Simple and reliable hub-and-spigot joints for pipes and fittings factory fitted with lip seals
• Easy and quick installation – low weight and centimetre scale printed on pipes
• High mechanical impact strength
• Good resistance to chemicals from PH2 to PH12

Learn More

FLO.250.HOSE 2.5 Meter Grey Inlet Hose Learn More

50mm Grey Pipe clip for Push Fit Tubing. These sturdy pipe clips give a 20mm stand off from the wall and feature a lever system to enable a quick install and easy removal. Quickly and easily assemble drainage works or use as drainage pipework from combi ovens. Can withstand temperatures of up to 95 degrees C.

• Pipes and fittings manufactured in a single-layer technology, with a thick-walled section, using a perfected raw material formula
• 100% recyclable pipes and fittings
• Simple and reliable hub-and-spigot joints for pipes and fittings factory fitted with lip seals
• Easy and quick installation – low weight and centimetre scale printed on pipes
• High mechanical impact strength
• Good resistance to chemicals from PH2 to PH12

Learn More

350 x 350mm - Core size 41 x 41mm - 100mm high- 10mm Pre Drilled Holes Learn More

DF-FX-400 FX 400 + Pre-Galv Channel 400mm 95mm high 180mm width Max Load 400Kg Learn More

DF-FX-600 FX 600 + Pre-Galv Channel 600mm 95mm high 180mm width Max Load 450Kg Learn More

50mm Plastic Push Fit Stop Cap. Quickly and easily assemble drainage works or use as drainage pipework from combi ovens. Can withstand temperatures of up to 95 degrees C.

• Pipes and fittings manufactured in a single-layer technology, with a thick-walled section, using a perfected raw material formula
• 100% recyclable pipes and fittings
• Simple and reliable hub-and-spigot joints for pipes and fittings factory fitted with lip seals
• Easy and quick installation – low weight and centimetre scale printed on pipes
• High mechanical impact strength
• Good resistance to chemicals from PH2 to PH12

Learn More

304 Stainless steel rear exit tundish 304 Stainless steel rear exit tundish for Combi Oven installations, welded 1 1/2" BSP thread to underside. 4 pre drilled holes for wall mounting, with support bracket. Stainless tundish's are widely used on combination oven installations that require an air break on the waste system. Install it on a solid wall, connect either iron or heat resistant plastic fittings to the 1 1/2" BSP connection and join into existing drain pipework. Using either a combination oven drain kit or stainless push fit drain system, easily pipe down and over the tundish. By using the tundish installation, you allow heat to escape from the drain and it also allows the equipment owner to easily move the oven for cleaning without the worry of cracking a hard plumbed drain. 140mm wide x 150mm deep x 180mm high Height includes 2 x 30mm fixing plates, Total overall height 175mm Depth includes 50mm connector on rear. Learn More

Hydraulic oven fan wheel puller set. This is suitable for removing the fan wheels from ovens such as Houno, Rational, Electrolux etc. For removing bearings, gears, sprockets and bushes. 10 ton capacity hydraulic ram with tommy bar. Metal storage case.
Set contains: 1 x 10 ton hydraulic ram. 1 x separator. 2 x 200mm main rods. 2 x 230mm extension rods. 1 x beam. 1 x ram nut. 1 x 100mm ram extension. Please note: These are not original fan wheel pullers supplied by the OEM. Learn More